GT-41060-WWVV-Q, ITE Power Supply, 60601-1-4th Ed. , Wall Plug-in, Regulated Switchmode AC-DC Power Supply AC Adaptor, , Input Rating: 100-240V~, 50-60 Hz, Blade Options for Q Series Wall Plug-in Power Supplies, Output Rating: 15 Watts, 3.0-30V in 0.1V increments, Approvals: RCM CE CE WEEE Double Insulation VCCI RoHS FCC NrCAN NEMKO CCC China RoHS IRAM PSE UL/cUL LPS Level IV 115V Ukraine Korea (12V Only) Singapore (12V only) CB IP52 Option IP40 PSE India
Regulated Switchmode AC-DC Power Supply AC Adaptor / 开关整流电源
Category
ITE Power Supply / 通信电源
Input Voltage Range (V)
100-240V~, 50-60 Hz
Max Input Current (A)
0.6 A
Max Output Power Rating (W)
15
Output Voltage Range (V)
3.0-30
Efficiency
IV
Ingress Protection
IP40
Size (mm)
84.0* 56.0*37.9
Enclosure
Rating Table
Model Number (Final ordering #/Part No to be defined)
Voltage
Amps (A)
Watts (W)
RFQ
GT-41060-1003*
3
3.3
9.9
GT-41060-1505-1.7*
3.3
4.54
14.98
GT-41060-1505-1.0*
4
3.75
15
GT-41060-1505*
5
3
15
GT-91125-15005*
5
30
150
DSA-1501*
5
3
15
DSA-1505*
5
3
15
HES61-30*
5
3
15
GT-348-6-1000D*
6
1
6
GT-41060-1706*
6
2.8
16.8
GT-41060-1809-1.5*
7.5
2.4
18
GT-41060-1809*
9
2
18
GT-51084-12N12-JP*
12
3
36
GT-41060-2512*
12
2.08
24.96
GT-41060-2515*
15
1.66
24.9
GT-41060-2518*
18
1.38
24.84
GT-41060-2520*
20
1.25
25
GT-41060-2524*
24
1.04
24.96
DA-60-24*
24
2.5
60
GTMDT66A-25.2-2500-3*
25.2
2.5
63
GT-41060-2530*
30
0.83
24.9
GT-41060-2548*
48
0.52
24.96
* (Final ordering #/Part No to be defined)
Specifications
A) ELECTRICAL SPECIFICATIONS:
1. Input Voltage: Specified 90-264 Vac, Nameplate rated: 100-240Vac
2. Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60Hz
3. Output Regulation: +/- 5% measured at the output connector
4. Line Voltage Regulation: +/- 1% maximum at full load
5. Output Ripple (Vp-p): 1% or 150 mV whichever is greater measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of output connector at nominal line
6. Turn-On/Turn-Off Overshoot: 5% maximum, 500uS maximun recovery time for 25% to 50% step load
7. Turn-On Delay: 3000 mSEC maximum at full load, 115VAC
8. Hold-Up Time: 10mS minimum at nominal input and full load
9. Inrush Current: 30A typical at 115VAC input and 60A typical at 230 VAC input
10. Switching Frequency: 65 KHz typical
B) PROTECTION
1. Over-Voltage: Protected, unit will recover upon removal of fault
2. Over-Load: Protected, unit will recover upon removal of fault
2. Short Circuit: Protected, unit will recover upon removal of fault
3. Input Protection: Input line fusing
C) SAFETY
1. Dielectric Withstand Voltage: 4242Vdc from primary to secondary
2. Touch Current: <0.25mA @ 240Vac input voltage
D) OTHER:
1. MTBF: 200,000 hours @ 25°C ambient temperature
2. Operating Temperature: 0°C to 40°C ambient temperature
3. Humidity: 0% to 90% relative humidity
4. Storage Temperature: -40°C to 80°C
5. ROHS 2: Complies with EU 2011/65/EU & CHINA SJ/T 11363-2006
E) ENCLOSURE
1. Upper Housing: High impact plastic, 94V0 polycarbonate, non-vented
2. Lower Housing: High impact plastic, 94V0 polycarbonate, non-vented
3. Size: 84.0* 56.0*37.9 mm +/-1.0
4. Green LED indicator for power "Power On"
INPUT CONNECTOR: Q-Socket (below are available blades configurations which are "not included" (unless stated above); can be purchased separately, package with power supply or as a separate "Q-KIT" if specified
01. United States / Canada / Japan NEMA 1-15P/IEC PLUG A[WORKS IN PLUG B] configuration: NA 2 blades, Class II; US/CA/JP P/N: Q-NA(R) 02. Australian AS 3112 configuration: SAA 2 blade/IEC TYPE I, Class II; AU P/N: Q-SAA(R) 03. UK BS 1363 configuration: UK 3 blade with dummy Ground/IEC TYPE G, Class II; GB P/N: Q-UK(R) 04. European CEE 7/16 configuration: Europlug 2 pins/IEC TYPE C [WORKS IN TYPE E&F], Class II; EU P/N: Q-EU(R) 05. Korean KS C8305 configuration: 2 pins/SIMILAR TO IEC TYPE C, Class II; KR P/N: Q-KR(R) 06. Argentina IRAM 2073 configuration: 2 blades/SIMILAR TO IEC TYPE I; AR P/N: Class II Q-AR(R) 07. China GB 2099 configuration: 2 blades/SIMILAR TO TYPE A, Class II; CN P/N:Q-CN(R) 08. India IS 1293 6A/BS546 configuration: 5A, 3 pins with Dummy Ground, Class II/IEC TYPE D; IN P/N: Q-IN(R) 09. IEC320/C18 Inlet, Class II; P/N:Q-C18(R) 10. Brazilian NBR6147 configuration: 2 pins, Class II;SIMILAR TO IEC TYPE C BR P/N: Q-BR(R) 11. South Africa SABS164-1, 3 round prongs, Class II + dummy ground, IEC TYPE M P/N: Q-SANS164-1-16A(R) 12. South Africa SABS164-4, 3 round prongs with a notched prong @ 0º, Class II + dummy ground, IEC TYPE M Red, P/N: Q-SANS164-4L-16A(R) 13. South Africa SABS164-4, 3 round prongs with a notched prong @ -53º, Class II + dummy ground, Blue, IEC TYPE M, P/N: Q-SANS164-4C-16A(R) 14. South Africa SABS164-4, 3 round prongs with a notched prong @ +53º, Class II + dummy ground, Black,IEC TYPE M P/N: Q-SANS164-4R-16A(R)
Contact GlobTek for your specific requirements or custom solutions.
Approvals
Logo
Description
Bureau Of Indian Standards for GT-41060-2512
No Logo
CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
CCC to GB4943.1-2011; GB/T9254-2008 GB17625.1-2012, Tropical <2000
CE Mark: tested to comply with EN55022:2006/A1:2007 Class B, EN610003-2, EN610003-3 including EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6N EN61000-4-11; EMI: Complies with EN55011 CLASS B and FCC Part 15B - On label or Molded in case
CHINA SJ/T 11364-2014, China RoHS Chart: http://en.globtek.com/globtek-rohs.php
UL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
Certification # TC RU 0585806 Custom Union of Russia, Belarus and Kazakhstan
FCC PART 15 CLASS B
Indoor Use Only - Mark is on the label or Molded in the case
IP40
Ingress Protection: IP40 to IEC60529:2001 Protection against
granular foreign bodies
IP52 OPTIONAL
Ingress Protection: IP52 to IEC60529:2001 Protected against dust - limited ingress (no harmful deposit) and Protected against direct sprays up to 15 degrees from the vertical
PRECAUCION: PARA USO EN EQUIPOS ELECTRONICOS SOLAMENTE
IRAM certificate DC-E-G71-002.1 to IEC 60950 + A1:2009
JAPAN TUV R-PSE, Cert. No. JD 50314327, to J60950-1(H26) , J55022(H22),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: http://en.globtek.com/importing-ite-and-medical-power-supplies-ac-adaptors-to-japan/
Korea KET KC Mark GT-41060-2512 HU10173-10024A (12V Only)
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
JAPAN TUV Rheinland-PSE GlobTek Inc to J60950-1(H26) , J55022(H22),J3000(H25).Please follow the procedure listed in the following link for proper import to Japan: http://en.globtek.com/importing-to-japan.php.
Australia and New Zealand Regulatory Compliance, Mark (http://rcm.standards.org.au/rcmfaq/rcmfaq.htm
RoHS
Specifications of directive 2011/65/EU Annex VI (ROHS-2) with amendment 2015/863-EU (ROHS-3) http://www.ce-mark.com/Rohs%20final.pdf
Singapore GT-41060-2512 ICE 60950-1:2001 + 2009 100599-12 (12 v only)
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
137567
5
3
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
195908
7.5
2.4
Female Barrel Right Angle 4.75*1.7*9.5mm with internal Spring Clip and Locking Notch or Equal
239228
9
2.7
Female Barrel 5.5*2.1*9.5mm No internal Spring Clip nor Locking Notch or Equal
News Releases
Title
Web Link
LPS Power Supply in Class II double insulated 24W (Watt) Interchangeable blade wall plug in mechanical configuration updated to latest Taiwan standard CNS 14336-1 (2010) - Safety - Part 1: General requirements and the latest editio[[[[[full title below]]]
GT-41060-WWVV-Q
中文 (Chinese)
Deutsch
English (Canada)
English (UK)
English (US)
Español
Finnish
Français
Italiano
Norsk
Polish (język polski)
Russian (русский)
Svenska
Türkçe
ελληνικά (Greek)
日本語 (Japanese)
한국의 (Korean)
Português